CDROM Icon Missing - Comments

Hi Bob, good article, and useful! I just want to point out one other culprit, one i personally dealt with: the Sony Rootkit that was a hot ticket a few months ago on the web, did exactly that to me! so....ya never know!!

I find in helping out at castlecops forum this come up many times! If the drive is showing in device manager. Than removing the drive from the device manager and rebooting works for quite a few cases.

Not in my case it didnt. I had a machine at work today which had these very symptoms, even tried putting another cdrom in. Still no joy. After following the registry fix given on this site, it worked spot on! Great fix, thanks!

Registry entry worked perfect.
Mate had this excact same problem and spent days trying to nut it out, Thanks heaps!

I had the same problem but with different results after do this procedure. Now my CD Rom dont wants to read any type of CD. It's come stuck with message: Device not responding. What can be?

EDITOR'S NOTE: Have you tried the drive in another machine? Tried another drive in this machine?

I use windows XP and 2000, my CD Rom is missing in windows XP while I can see it in CMOS settings. Its also not listed in device manager. I tried the registry tweek but there was only the "LowerFilters" entry, I deleted and rebooted my PC still no luck. My CD Rom works fine in windows 2000 installed in the same PC. Pls help.

EDITOR'S NOTE: It seems your XP install is damaged. You might want to try http://www.askbobrankin.com/missing_or_damaged_dll_files.html

I have a DVD (master) and a CDROM (slave) installed on a machine running Win2K pro. About 3 weeks ago the CDROM quit working. I had both icons, device manager recognized both drives, the lights would blink on the drives, but I could not read any type of CD. I figured the CD must be dirty or have an electronics problem. I sprayed compressed air into the drive. Still didn't work. I then replaced the data cable. It still would not read a CD. About two days ago I noticed the DVD quit working. I figured this could possibly be a power supply problem or the onboard controller maybe going bad.

On bootup windows would recognize the drives, but I had no icons for the DVD or CD and the error given by device manager was : "A driver for this device was not required, and has been disabled. (Code 32) "

That didn't make a bit of sense to me so I removed the hardware in device manager and rebooted. Windows says it found new hardware and to reboot again for the change to take effect. After rebooting I still had no icons.

I was about to open the case and check the power supply cables to each drive and needed the pinout info. While researching that on the internet I discovered your site and tried your registry fix. What a blessing. Both drives now work. I was so desperate to keep from reinstalling windows and all my software that I would have settled for just one drive working.

I had been installing and uninstalling some programs lately and feel that was what caused this problem. Thanks for the registry fix info. It saved me a lot of work and frustration.

thanks i hack the system like u said and it brought it all back to normal

Hi ya, installed universial usb drive (nusb22e setup for windows 98SE)and this caused some sort of conflict with my in my secondary IDE controller- has yellow exclamation "code 10". My CD-rom/ DVD-rom icon in my computer have disappeared. Tried the safemode delete of all cd-rom dvd-rom refs in device manager and reboot to let windows redetect the devices. Unfortunately no joy. CD-ROM has disappeared from my devices but DVD-ROM is present but has a X over it, and same warning for secondary IDE. The icon is still absent for the drive (D: drive). I did remove all previous usb drives before nusb22e install, and I pretty sure it's the nusb22e drive that's done it. However, I can't remove nusb22e because I don't know where it put all the files and isn't in the add/remove program list. Any help at all would be welcome please. Oh nusb22e works fine as a universial...I just can't access my cd-rom/dvd-rom, bummer. Thanks

EDITOR'S NOTE: Did you try the registry trick mentioned in this article?

Hi, I looked in the registry but in the Windows 98 SE folder: 4D36E965-E325-11CE-BFC1-08002BE10318, there were three entries called CD-ROM. I didn't delete them because they were not the same as the entries in the example above. However after experimenting (disabling both primary and seconday IDEs via the master IDE, rebooting, and then re-enable both IDEs, then reboot). This redetects my CD-rom/DVD-rom drive and the drive icon reappears (ROM works fine). Unfortunately once the computer is rebooted the error message reappears and the drive icon goes missing and there is a cross on the ROM drive in device manager.

The above happens everytime and I end up with the original problem of no DVD/CD-ROM. If I delete the CD-ROM registry entry will that make any difference? Also is it possibly to uninstall CD-Rom driver and reinstall (might be corrupt, but not sure how to do it). Thank you for any help.